My Account Checkout View Cart Shipping & Returns Contact Us                   
Amazing Crafting Productsalumilite logo
pinterest  pinterest  twitter  blog  facebook  youtube                                                                   
Gallery      Instructions      Products       Workshops      Retailers      FAQ      User Forum      Blog      Facebook

Home > Frequently Asked Questions

Search FAQ & User Forum for help:

Select a question from the categories below:
Amazing Mold Putty
- How critical is the mix ratio of the Amazing Mold Putty?
- Does the Amazing Mold Putty come in any other color?
- Why is my Amazing Mold Putty sticky on the surface of my mold?
- Can I bake my cured Amazing Mold Putty mold?
- Can I pour low melt metals into my Amazing Mold Putty Mold?
Amazing Casting Resin
- How do I avoid air bubbles in my part?
- What is the best way to pour my part to eliminate air bubbles that are formed when pouring?
- Can you vary the mix ratio of the Amazing Casting Resin?
- Can I get more work time out of the Amazing Casting Resin?
- Why is my cast piece soft?
- Is the Amazing Casting Resin cured piece UV stable?
- Can I paint the Amazing Casting Resin piece?
- Why is my Amazing Casting Resin foaming?
- Can I put any filler into my Amazing Casting Resin?
Other
- Do you have any other types of mold making and casting products?

Amazing Mold Putty
How critical is the mix ratio of the Amazing Mold Putty?
The proper mix ratio is 1:1 by either weight or volume however, the Amazing Mold Putty is very forgiving and will cure even if you are off fairly significant amounts in either direction. Changing the ratio will not alter the speed in which the putty cures although it may change the physical properties and the finished mold may not be as tough or ever reach its optimum hardness.

top
Does the Amazing Mold Putty come in any other color?
The Amazing Mold Putty has a sister product which is Purple. The primary difference between the two formulations is that the Purple is faster. The work time of the Purple is 1.5 minutes and the demold time is less than 10 minutes. This works well if you are doing small molds and do not wish to wait 20 minutes for your mold to harden/cure. It does not work very good when you need to mix up slightly larger amounts due to the time required to mix it thoroughly does not give you much time to roll the mixed putty into a ball and press it over your item. Therefore the Yellow Amazing Mold Putty gives you a more user friendly 4 minute work time and a 15-20 demold time.

If you wish to purchase or look at the Purple putty, please visit our corporate website at www.alumilite.com and then hit Products, Silicone Rubber, and then you will find the Mold Putty which is the faster purple version of the Amazing Mold Putty.

top
Why is my Amazing Mold Putty sticky on the surface of my mold?
The Amazing Mold Putty is a platinum based silicone mold rubber. The platinum base can become contaminated when it comes in contacts with specific materials ... such as tin, sulfur, and vinyl. These products are often found in clays, tapes, glues, plastics and some rubber stamps.

What will happen is where ever the putty comes in contact with one of these different materials, they will simply not cure. However, every where the putty does not come in direct contact with the materials, it will cure absolutely fine.

If you are not sure whether the item you are about to mold using the Amazing Mold Putty contains one of these materials, it is highly recommended to mix up a very small batch of the putty and press it over a small area of your piece. Allow it to sit for 20 minutes and then remove. Notice the surface of both your original as well as the mold. Drag your finger across the surfaces to see if the mold surface smears. If it does, I would not recommend making the mold until you have either completely coated the original to protect the putty from the surface or simply choose type of master to test and then mold.

top
Can I bake my cured Amazing Mold Putty mold?
Yes. Amazing Mold Putty is food grade compliant up to 395 degrees F. This enables you to either bake food, polymer clay, or any other type of material in the mold without harming it.

If you plan to use the mold for food, do not use it with any other material before putting your food product into the mold to eliminate any possibility of contamination.

The Amazing Mold Putty is a very good insulator of heat, so it is highly recommended to preheat your mold as you preheat your oven to provide a more even bake process when baking food. Otherwise, your food product may cook on top but because of the thickness of your mold, the heat will take much longer to reach the food in the mold cavity and make for an unevenly cooked product.

top
Can I pour low melt metals into my Amazing Mold Putty Mold?
Yes. The Amazing Mold Putty will handle temperatures above 395 F but is not recommended for food above those temperatures. To provide the best mold life and the best detail reproductions when pouring low melt metals into your mold, it is highly recommended to preheat the cured mold in the oven to bring it up to a similar temperature before pouring the molten metal into the mold. This prevents the metal for solidifying as soon as it touches a cold mold and prevents a quick skin from forming. So preheat the Amazing Mold Putty mold to achieve more consistent castings and a longer mold life.

top

Amazing Casting Resin
How do I avoid air bubbles in my part?
Cast the Amazing Casting Resin into a warm mold coated with baby powder. This will help the material flow better and cure more evenly. If you are using an Amazing Mold Putty mold, stick the mold in an oven set at "Warm" for approximately 30 minutes or put your mold in a microwave on high for 1 minute per lb of rubber. Once your mold is warm to the touch, sprinkle baby powder or talc powder in the mold. Shake the powder around the mold so all areas are covered. Once covered, knock or blow out all of the excess powder. This will leave a light coat of powder on the outside of the mold that will release the surface tension and allow the material to flow much better reducing the chance of trapping air bubbles. You can also use any kind of paint or commercial brand of urethane release to aid in the problem if baby powder isn't available. For complex molds that have severe undercuts, you may need to vent those troubled areas with holes that can be created with either some copper tubing or an Excel or Exacto knife.

top
What is the best way to pour my part to eliminate air bubbles that are formed when pouring?
If you are casting a part in an open or one piece mold, pour slowly from one corner of the mold and let the material flow naturally to fill the mold. If it is possible run the material down one side of the mold. If the mold has an undercut or complex corner you may pour the material to that point and then rotate your mold to evenly coat that area before topping off the mold. If you are pouring a closed or two piece mold, fill it completely until the material comes out of the vent hole and then tap the mold on the table to release any bubbles that may need a little assistance to get through the vent hole. You may also wish to rotate the mold and possibly squeeze the sides of the mold to assist hesitant bubbles in reaching the vent.

top
Can you vary the mix ratio of the Amazing Casting Resin?
No. Varying the ratios will not affect the working time but it will affect the cure time and physical properties. Meaning, the Amazing Casting Resin will still start to set up in it's normal time but could take hours to completely cure. When it finally does cure, it will not have the same properties of the properly mixed resin and may be considerably weaker.

top
Can I get more work time out of the Amazing Casting Resin?
Yes! To get an additional 30 - 60 seconds, cool or chill both sides of the Amazing Casting Resin in the refrigerator for an hour before mixing. When you cool the resin it is important to remember to pour into a warm mold for proper curing, especially when you are pouring small or thin parts to enable the resin to cure properly.

top
Why is my cast piece soft?
Typically, the reason your Amazing Casting Resin piece is soft is that the part you poured is small or thin and the resin was poured into a mold that was room temperature or even worse ... cold. The Amazing Casting Resin is exothermic, which means it generates heat as it cures. The resin needs this heat to cure properly. If the part is small and or thin and poured into a cold mold, it does not have the ability to generate the heat required to cure fully. So the material will gel and start to cure but not finish because it is lacking the heat necessary to finish curing properly. With your piece in the Amazing Mold Putty mold, simply place it in an oven at 150F or less for an hour or place it under a heat lamp for a couple hours to supply the cast piece some heat in order for it to cure.

top
Is the Amazing Casting Resin cured piece UV stable?
No. The Amazing Casting Resin is opaque White and will yellow slightly over time if it is exposed to UV light. Clear acrylics or lacquers work well for protecting the resins from changing color. There are two ways of applying paint to achieve the best adhesion. First paint the mold and allow it to completely dry before casting your resin. As the resin flows into the painted mold, it will chemically bond to the paint as the resin is curing and after the resin cures you will demold a perfectly painted part. Painting the mold prior to casting allows you to reproduce perfect detail by painting becoming the outside layer of the actual part rather than cover the exact cast replica with paint that could then cover up fine detail. The other option for painting your part is to paint the part as soon as you remove the cast part from the mold and after you remove any flash while the resin is still curing. Although the resin is demoldable, the casting resin is still curing and if painted during the first 5 or 10 minutes of casting the part, the resin will still crosslink with the paint to give you not only a mechanical bond but also a chemical bond between the paint and the cast piece. Paints have built in UV stabilizers which then block out the UV light from ever reaching the casting resin which could affect the color.

top
Can I paint the Amazing Casting Resin piece?
Yes! We recommend lacquers or acrylics but you may also use synthetics or enamels. A lacquer primer may be needed to assure the long tem effectiveness of the paint. You may wish to paint your silicone mold before casting. Paint the mold with a fast drying acrylic or clear coat. Once it is completely dry, cast your piece. When you demold the part you will pull out a painted piece. The Amazing Casting Resin will chemically bond to the dried paint. The other option is to paint the part as soon as it comes out of the mold while the resin is still curing to allow the curing resin to crosslink with the paint.

top
Why is my Amazing Casting Resin foaming?
Moisture contamination in urethanes causes foaming. If it foams quite a bit, most likely the moisture is right in the Amazing Casting Resin. The moisture is usually in the A-side. There is not a full proof method of removing moisture from your system. Typically the B side will crystallize when moisture is present. The A side, however, will not look any different.

Moisture is absorbed through the air and therefore is very important to put the caps back on the bottles as soon as you are done measuring out the amount you need for your next pour. Do not leave the caps off for any extended period of time.

top
Can I put any filler into my Amazing Casting Resin?
Yes. You may use any DRY filler and add it to your A & B prior to mixing the two equal parts together to achieve different looks, weight, or density to your cast piece. If there is any moisture in your filler, it will make the resin foam. Therefore, make sure your filler is dry. Examples of types of fillers would be: playground sand ... gives you a fine granite or sandstone look, porcelain ... for cold cast porcelain, aluminum ... adds weight, etc.

top

Other
Do you have any other types of mold making and casting products?
Yes, we have an entire line of liquid silicones, rigid and flexible urethane casting resins, foams, equipment, tools, fillers, and more.

Alumilite is our parent site. Amazing Mold Putty and Amazing Casting Resin are the pioneer products of our Craft line. Please visit us online at www.alumilite.com or call us toll free at 800 447-9344 for any mold making and casting question you may have. We'll be happy to spend the time on the phone to help you with your project.

We're open Mon-Fri 8am-5pm EST.

top

Not finding the information you need? Try our User Forum for more online advice!
 

Have questions? Call 1-800-447-9344 or search our FAQ & User Forum:

Part of the ALUMILITE Family of Sites:
Alumilite CorpHunt for Big FishAlumilite CorpHunt for Big Fish

Gallery | Instructions | Products | Workshops | Retailers | FAQ | Q & A Forum

My Account | Check Out | View Cart | Shipping & Returns | Contact Us

 
home youtube facebook